Jet JW1015 4-Inch, A Strong Link in the DC..
| Overall Rating |   |
|
A Strong Link in the DC Chain
This is a good connector for a DC system. Not a complicated piece, but a very good one. The ends were all 4″ , the hose fit snuggly and the wire clamps held.When making a branch in the DC system, to go to several different pieces of equipment, the “Y” connection is better to use than the “T”. The Y will allow for a better air flow. Combine the Y with a/several blast gates, then it’s almost like having a single hose go to each piece of equipment.
Update (2/6/2012):
The featured review for this product, Jet JW1015 4-Inch Y-Fitting Dust Hose Connector Tools & Hardware, was written by David Lindamood.
The average rating for this item is out of 5 stars, according to 3 reviews.
- Related posts on accessories
- Know more information about your psp accessories | BuyPSPConsole.com
- Hottest Holiday Games and Accessories – Santa's Most Wished for …
- What Type Of MP3 Player Accessories Do I Need? | 9MONTRI'Blog
- Related posts on blast gate
- Dust Collection Fitting, Blast Gate Self Clearing, ABS, 4-inch OD …
- PSI Woodworking LRMSET220 220 Volt Long Ranger Multigate Switch …
- Dust Collection Fitting, Blast Gate, Steel, 4-inch OD | Cheap work …
- Related posts on dust
- Cap your PC with a computer cover » OnlyHardwareBlog
- DUST CONTROL STRATEGY | WhiteFace Builders
- O Cedar MaxiClean Microfiber Dust Mop 36in x 5in 6 EA 96074 …
Related posts:
- Jet JW1036 6-Inch x, beyond my expectations
- PSI LRMSET110 Long, A unique item
- JET JW1317 4-inch Wire, The Best Clamp…The Best..
- Jet JW1026 2-Inch by, Good consistent Hose
- Mighty Mule FM143, Strong security, protect..
Tags: accessories, blast gate, dust, dust collection, fittings, hose, hoses, jet, ng
Posted on: August 16, 2010
Filed under: Reviews
Reviews (3)
Bob Feeser
August 8th, 2010 at 1:59 pm
Does a Great Job
When installing a dust collection system, eliminating resistance to airflow is what it is all about. The ideal is as large a pipe as possible, flowing in a straight line, without any ridges in the surface. Of course in the real world at least some of these things wind up being less than ideal. What this Jet 4″ Y-connector does, is give you a large pipe, that makes a gradual Y as opposed to a straight 90 degree angle T, and the sides of the connector are smooth. So when you need to divide your air source into two lines, this elbow does the nicest job. The advantage of incorporating a Y connector into your system, is that you can take a single air source, connect this Y connector to it, a pair of gates, and no longer have to switch your hoses between two different pieces of equipment. All you do is open the gate to one, and close it to the other. All in all highly recommended.
Scott Pointon
August 9th, 2010 at 10:31 pm
Great DC fitting!
Like all of my Jet dust collector fittings, I have been very pleased with the performance of this “Y” fitting, and it was much MUCH cheaper at my local Menards. I used these Y’s in my main duct to create branches for my stationary tools on the long wall of my shop. The 4″ size was perfectly consistent and always fit the ducting and flex hose without any trouble. The “Y” design greatly reduces any loss of air flow as compared to elbow fittings and the plastic is very strong and rigid.
Highly recommended as an essential accessory for any dust collection system.
David Lindamood
August 10th, 2010 at 5:04 am
A Strong Link in the DC Chain
Rated 4 stars.
Leave a reply